Cameras and combinations not listed here have not been tested. Please note that we are unable to answer any questions regarding the operation of these cameras.
FP/HSS (High Speed Synchro) flash is supported only in combination with a camera equipped with this function.
AF-assist lamp is not supported on Mirrorless cameras.
For Canon (On-camera mode and Commander mode*1)
The following camera names are listed by their Japanese names.
If you have a product for North America, Europe, or Asia, please use this link to look up the Japanese name.
EOS-1D X Mark III / 1D X Mark II / 1D X / 1D Mark IV / 1D Mark III
EOS 5D Mark IV / 5D Mark III / 5D Mark II
EOS 6D Mark II / 6D
EOS 7D Mark II / 7D
EOS 90D*2 / 80D / 70D / 60D / 50D / 40D
EOS 9000D / 8000D
EOS Kiss X8i / X7i / X7 / X6i / X5 / X4 / X3 / X2 / F
EOS Kiss X90 / X70 / X50
EOS R10*2 / R7 / R6*2 / R5 / RP / R
The following cameras are not compatible with this product. PowerShot series / EOS M5 / M3 / M
*1 2nd curtain sync in commander mode is not supported. *2 Operation in commander mode is under verification.
Remark: When setting this unit to slave mode and controlling it from a commander other than MG80 Pro (Air10s, etc.), check the compatibility chart for the commander to be used.
For Nikon(On-camera mode and Commander mode)
Z 9 / Z 8*1 / Z 7II*2*3 / Z 7 / Z 6II*2*3 / Z 6 / Z 5 / Z 50 / Z 30*1 / Z f / Z fc*4
D6 / D5 / D4s / D4 / D3X / D3s / D3 / Df
D850 / D810 / D800 / D800E / D780 / D750 / D700 / D610 / D600
D500 / D300s / D300 / D200 / D90
D7200 / D7100 / D7000
D5600 / D5500 / D5300 / D5200 / D5100 / D5000
D3300 / D3200 / D3100 / D3000
The following cameras are not compatible with this product. D2Xs / D2Hs / D2H / D100 / D1 / COOLPIX series
*1 When in commander mode, this unit (A’ group) tends to overexpose. *2 When this speedlight is used in on-camera mode, the flash may not fire normally in the release mode H+ (Continuous H (extended)). *3 When controlling the MG10 / MG8 with the Commander mode of this speedlight, if a shutter speed exceeding the sync speed is used, the TTL light control function will not work properly. *4 To use with Z fc, please update the camera firmware version to 1.20 or higher.
Remark: 1. When controlling AirR (for Nikon), the AirR firmware must be version 4 or later to operate properly. Please make sure to check the firmware version of AirR. 2. When setting this unit to slave mode and controlling it from a commander other than MG80 Pro (Air10s, etc.), check the compatibility chart for the commander to be used.
For Sony(On-camera mode and Commander mode)
α7 / 7 II / 7 III / 7 IV / 7s / 7R II / 7R III / 7R IV / 7R V*1 / 7C / 9 / 9 II
α6000 / 6300 / 6400
77 II / 99 / 99 II
ZV-1*2*3
Cyber-shot RX1 / RX10 / RX10 III / RX10 IV / HX60V
The following cameras are not compatible with this product. α3000 / RX100 II
*1 Commander mode tends to underexpose in TTL mode.
*2 Since it uses a lens shutter, it can synchronize up to a shutter speed of 1/2000 second without switching. *3 Commander mode is not available because the camera does not have “WL (Wireless)” in its flash mode.
Remark: 1. The light compensation function of the camera may not work properly with some cameras. The strobe’s light compensation function works properly.
2. It has been confirmed that the High-Speed Synchro (HSS) function does not work properly (does not synchronize or does not fire) in Commander mode or Slave mode depending on some cameras or camera firmware versions. We are currently working on the firmware upgrade, so please wait for the next update. (The camera works fine in on-camera mode) 3. When using this speedlight in commander mode, the flash mode must be set to [WL (Wireless)] or the wireless flash function must be set to [On] in the camera menu to work properly. 4. When setting this unit to slave mode and controlling it from a commander other than MG80 Pro (Air10s, etc.), check the compatibility chart for the commander to be used.
